top of page

Co Print Quadro on Kickstarter: Multicolor 3D Printer With Four Independent Toolheads

Writer: Jonathan
Jonathan
6 hours ago
7 min read
Co Print Quadro 4-toolhead 3D printer showing its four independent print heads, 300 x 300 x 300 mm build volume and external filament spools.

Print a four-color model on a single-nozzle machine and the waste can outweigh the model itself. Every color change pushes the old filament out of the nozzle, and the pile grows beside the plate. The Co Print Quadro is a multicolor 3D printer with four independent toolheads on one rail, each loaded with its own filament.


Co Print brings the Quadro to Kickstarter after delivering two campaigns, the MFM module in 2021 and ChromaSet in 2023, to more than 1,500 supporters. All3DP described the Quadro as "unlocking proper multi-material printing, not just cosmetic color changes." The Co Print Quadro price on Kickstarter is $649 for Super Early Bird backers.


When you purchase through links on our site, we may earn an affiliate commission. Here’s how it works.


🚀 Co Print Quadro campaign: on Kickstarter until December 7, 2026

📈 In its first week: $455,817 raised from 600 backers, goal $9,882

💰 Tiers: Super Early Bird $649 (limited to 500), Early Bird $699 (limited to 500), Quadro Complete Pack $899 (limited to 300)

📦 Delivery: estimated February 2027



Quick Verdict


Our verdict: 8.5/10


Who Is It For?


This 4-toolhead 3D printer suits hobbyists who print multicolor figures, cosplay pieces and gifts. Engineers who mix materials in one job, and small shops or print farms running batches, also fit.


Main Strengths


  • Four toolheads stay mounted and loaded on one axis, so a color change takes about a second, with nothing swapped.

  • Colors never share a nozzle, so there is no purge pile, and compatible models can skip the prime tower too.

  • All four heads reach the full Co Print Quadro build volume of 300 x 300 x 300 mm, for large pieces in one job.

  • Up to four materials print at four temperatures, and all four heads calibrate automatically.

  • Two pairs of heads can build two copies at once, each in two colors, for up to twice the output on batches.


Main Limitations


  • The Quadro moves Co Print from upgrade kits to a complete printer, and its plan leaves only about two months between mass production in December 2026 and the first shipments in February 2027.

  • The open frame covers PLA, PETG, TPU, PVA and PLA-CF, so ABS and ASA require the optional $129 Quadro Enclosure.

  • CMYK full-color printing, mixed nozzle sizes in one print and print-farm management are still in testing, planned as free updates with timing that may change.


Is the Co Print Quadro Worth Backing?


The Co Print Quadro is worth backing for multicolor makers and small batch shops whose prints change colors or materials many times per job. Buyers who print mostly single-color parts can pass, since three of the four heads would sit idle. The deciding reason is the four heads that share one axis and never swap: the Co Print Quadro on Kickstarter .




Co Print Quadro Price on Kickstarter


The Co Print Quadro price on Kickstarter is $649 for Super Early Bird backers, limited to 500 units, against an $899 MSRP. The Early Bird is $699, also limited to 500. The tier we recommend is the Quadro Complete Pack at $899, limited to 300: it adds the Quadro Enclosure, four filament dryers, a Hotend Kit and an extra build plate. Shipments are scheduled to start in February 2027.


Bought separately, those extras would add about $310 to the Super Early Bird printer, so the pack saves roughly $60. The dryers keep PVA, TPU and PETG print-ready and the enclosure opens ABS and ASA, so the pack suits a buyer who plans to fill the heads with different materials; for PLA in four colors, the printer alone is enough. Our 3D printer reviews cover the other options, and the Complete Pack is $899 on Kickstarter .



What Is the Co Print Quadro and What Problem Does It Solve?


Co Print Quadro: A Four-Head Bed-Slinger for Color and Mixed Materials


The Co Print Quadro is a 4-toolhead 3D printer built as an open-frame bed-slinger, the layout most makers already know, made stiff enough to carry four heads at once. Each head has its own direct-drive extruder and hardened steel nozzle, with hotends reaching 300°C, and a light that shows the color loaded in it. The flexible PEI-coated steel plate heats to 100°C, and a 1080p camera watches the whole bed.


The printer measures 780 x 620 x 515 mm, ships in an 18 kg package and connects over 2.4 GHz Wi-Fi and USB. Co Print, with its team in Istanbul and support teams in the UK and US, has shipped its products to more than 10,000 makers in 64 countries. Production runs with Co Print's manufacturing partner in China, with CE, FCC and UKCA certification in progress.


Why Multicolor Printing Meant Waste and Waiting


Even a small four-color cube can mean 118 color changes, and on a single-nozzle multicolor 3D printer each one costs plastic: the old color is cut, unloaded and purged, straight into the bin. Tool and nozzle changers cut the waste, but every change still swaps hardware that has to stay aligned.


On the Quadro, a print with a hundred color changes runs straight through them, and far less of what you load ends up in the bin.



Co Print Quadro Key Features and Specs: Toolchange, Waste, Materials, Calibration


Co Print Quadro multicolor 3D printer printing a four-color model with four independent toolheads and multiple filament spools.

IQEX and a 1-Second Toolchange: Four Heads That Never Leave the Rail


Co Print calls the layout IQEX, for Independent Quad Extruder: the IDEX idea of two independent extruders on one gantry, extended to four on a single X-axis. Each head has its own motor, belt and pulley, so one slides aside as the next takes its place, after heating for about 30 seconds while the current head prints.


Co Print measured the move at 1.00 s from tool 1 to tool 2, 1.40 s to tool 3 and 1.57 s to tool 4, before any priming; a toolchanger such as the AXILOOP MC8 takes 4 seconds per swap. The same drives allow dual printing: heads 1 and 2 build one copy while heads 3 and 4 build another, so a model comes off the bed in two colorways.


QDock Station and Zero Waste Mode: No Purge Between Colors


A finished head retracts its filament about 1 mm and cools to around 140°C on the way to its QDock Station, where a heat-resistant cap seals the tip, so a parked nozzle cannot drip or string across the model. A small prime tower usually steadies pressure when a head resumes; on compatible models with enough infill, Zero Waste Mode does that inside the infill instead.


Co Print tested five four-color models against a toolchanger and a large-format single-nozzle printer, with the same sizes, 0.4 mm nozzles and 0.2 mm layers, and puts the Quadro up to 70% faster with up to 90% less waste. In a scale test, one model left 1,079 g of waste on a single-nozzle printer and 135 g on the Quadro.


300 x 300 x 300 mm and Four Materials: Big Prints at Four Temperatures


At 27.0 liters, the Co Print Quadro build volume is about 61% larger than a 256 mm cube, room for a full helmet without splitting and gluing. Every head reaches all of it, so the four colors are available anywhere on the 305 x 305 mm plate.


Each head holds its own material at its own temperature, with up to 24 mm³/s of flow, for rigid bodies with TPU 95A grips or PVA supports that dissolve in water. The hardened nozzles handle abrasive PLA-CF on the open frame, and the optional enclosure adds built-in air filtration.


360° Calibration, QuadrOS and Co Slicer: Four Nozzles, One Reference


A Full Self Check runs the whole calibration in one tap, in about seven minutes. Each nozzle touches a reference pin from five directions to align with tool 1, down to the micron by Co Print's rating; a load cell maps the plate with the nozzle itself, and input shaping cancels resonance. Flow is calibrated before every print, and pressure advance is tuned per filament.


QuadrOS runs on Klipper, and Co Slicer, built on OrcaSlicer, maps each painted color to its head and is already open source on GitHub; the QuadrOS source will follow.



Should You Back the Co Print Quadro on Kickstarter?


The Co Print Quadro is a multicolor 3D printer for people who print in several colors at once. A cosplayer prints a helmet in one piece, or a small shop runs the same part in two colorways side by side.


Co Print has been building color systems for 3D printers since 2019, and pilot-line units of the Quadro are already with reviewers. The Co Print Quadro price for Super Early Bird backers is $649, $250 under its MSRP; the printer alone is the entry point, and the Complete Pack is the tier to take for mixed materials: the Co Print Quadro is on Kickstarter .




FAQ about the Co Print Quadro on Kickstarter


How does the Co Print Quadro compare with the Snapmaker U1?

Both are 4-toolhead 3D printers. The Snapmaker U1 ships today and accelerates faster on a CoreXY frame, at 20,000 mm/s² against 10,000. The Co Print Quadro build volume is larger, a 300 mm cube against 270 mm, and its measured 1.00-second change is quicker than the roughly five seconds Snapmaker gives for a U1 swap.

Yes. The Co Print Quadro takes any 1.75 mm filament brand, with material presets on the touchscreen.

Not for PLA, PETG, TPU, PVA or PLA-CF, which print on the open frame. ABS and ASA need the optional Quadro Enclosure, a $129 add-on included in the Complete Pack.

One year, or two years in the EU, Switzerland, Norway and Iceland, with wear parts covered for three months; Co Print Care, a $78 add-on, adds a year. UK and US support teams reply within one business day, Monday to Friday.

Shipping is collected in a survey after the campaign, estimated at $69 to the UK, $79 to the contiguous US and $89 to Canada and the EU. Import duties and VAT are extra.

Yes. The Quadro Simulator at calculator.coprint3d.com takes a model sliced in any slicer, compares print time and filament waste, and shows how the four toolheads would print it.


About the Author


Jonathan, Co-Founder & Reviewer at GizmoCrowd

Jonathan

Co-Founder & Reviewer at GizmoCrowd


Jonathan is Co-Founder of GizmoCrowd and a crowdfunding strategist with over 15 years of hands-on campaign experience on Kickstarter and Indiegogo.


bottom of page